#include "core/powerSave.h" #include "core/utils.h" #include #include #include XPowersAXP2101 axp192; #include TouchDrvFT6X36 touch; // Haptic #include "SensorDRV2605.hpp" SensorDRV2605 drv; /*************************************************************************************** ** Function name: _setup_gpio() ** Location: main.cpp ** Description: initial setup for the device ***************************************************************************************/ void _setup_gpio() { pinMode(16, INPUT); // Touch IRQ Wire.begin(10, 11); // sensors delay(10); Wire1.begin(39, 40); // touchscreen delay(10); _rtc.setWire(&Wire); // Cplus uses Wire1 default, the lib had been changed to accept setting I2C bus // StickCPlus uses BM8563 that is the same as PCF8536 axp192.init(Wire, 10, 11); axp192.setVbusVoltageLimit(XPOWERS_AXP2101_VBUS_VOL_LIM_4V36); axp192.setVbusCurrentLimit(XPOWERS_AXP2101_VBUS_CUR_LIM_900MA); axp192.setSysPowerDownVoltage(2600); axp192.setALDO1Voltage(3300); axp192.setALDO2Voltage(3300); axp192.setALDO3Voltage(3300); axp192.setALDO4Voltage(3300); axp192.setBLDO2Voltage(3300); axp192.setDC3Voltage(3300); axp192.enableDC3(); // gps axp192.disableDC2(); axp192.disableDC4(); axp192.disableDC5(); axp192.disableBLDO1(); axp192.disableCPUSLDO(); axp192.disableDLDO1(); axp192.disableDLDO2(); axp192.enableALDO1(); //! RTC VBAT axp192.enableALDO2(); //! TFT BACKLIGHT VDD axp192.enableALDO3(); //! Screen touch VDD axp192.enableALDO4(); //! Radio VDD axp192.enableBLDO2(); //! drv2605 enable // Set the time of pressing the button to turn off axp192.setPowerKeyPressOffTime(XPOWERS_POWEROFF_4S); // Set the button power-on press time axp192.setPowerKeyPressOnTime(XPOWERS_POWERON_128MS); // It is necessary to disable the detection function of the TS pin on the board // without the battery temperature detection function, otherwise it will cause abnormal charging axp192.disableTSPinMeasure(); // Enable internal ADC detection axp192.enableBattDetection(); axp192.enableVbusVoltageMeasure(); axp192.enableBattVoltageMeasure(); axp192.enableSystemVoltageMeasure(); // t-watch no chg led axp192.setChargingLedMode(XPOWERS_CHG_LED_OFF); axp192.disableIRQ(XPOWERS_AXP2101_ALL_IRQ); // Enable the required interrupt function axp192.enableIRQ( XPOWERS_AXP2101_BAT_INSERT_IRQ | XPOWERS_AXP2101_BAT_REMOVE_IRQ | // BATTERY XPOWERS_AXP2101_VBUS_INSERT_IRQ | XPOWERS_AXP2101_VBUS_REMOVE_IRQ | // VBUS XPOWERS_AXP2101_PKEY_SHORT_IRQ | XPOWERS_AXP2101_PKEY_LONG_IRQ | // POWER KEY XPOWERS_AXP2101_BAT_CHG_DONE_IRQ | XPOWERS_AXP2101_BAT_CHG_START_IRQ // CHARGE ); // Clear all interrupt flags axp192.clearIrqStatus(); // Set the precharge charging current axp192.setPrechargeCurr(XPOWERS_AXP2101_PRECHARGE_50MA); // Set constant current charge current limit axp192.setChargerConstantCurr(XPOWERS_AXP2101_CHG_CUR_300MA); // Set stop charging termination current axp192.setChargerTerminationCurr(XPOWERS_AXP2101_CHG_ITERM_25MA); // Set charge cut-off voltage axp192.setChargeTargetVoltage(XPOWERS_AXP2101_CHG_VOL_4V35); // Set RTC Battery voltage to 3.3V axp192.setButtonBatteryChargeVoltage(3300); axp192.enableButtonBatteryCharge(); touch.begin(Wire1, FT6X36_SLAVE_ADDRESS, 39, 40); touch.setSwapXY(true); touch.interruptPolling(); // Disable RF and NRF Menus for default bruceConfig.disabledMenus.push_back("RF"); bruceConfig.disabledMenus.push_back("NRF24"); // Haptic driver if (!drv.begin(Wire, 10, 11)) { Serial.println("Failed to find DRV2605."); } else { Serial.println("Init DRV2605 Sensor success!"); drv.selectLibrary(1); drv.setMode(SensorDRV2605::MODE_INTTRIG); drv.useERM(); // Startup buzz drv.setWaveform(0, 70); drv.setWaveform(1, 0); drv.run(); } bruceConfigPins.gpsBaudrate = 38400; } /*************************************************************************************** ** Function name: _post_setup_gpio() ** Location: main.cpp ** Description: second stage gpio setup to make a few functions work ***************************************************************************************/ void _post_setup_gpio() { pinMode(TFT_BL, OUTPUT); digitalWrite(TFT_BL, HIGH); ledcAttach(TFT_BL, TFT_BRIGHT_FREQ, TFT_BRIGHT_Bits); ledcWrite(TFT_BL, 255); } /*************************************************************************************** ** Function name: getBattery() ** location: display.cpp ** Description: Delivers the battery value from 1-100 ***************************************************************************************/ int getBattery() { int percent = axp192.getBatteryPercent(); return percent; } /********************************************************************* ** Function: setBrightness ** location: settings.cpp ** set brightness value **********************************************************************/ void _setBrightness(uint8_t brightval) { int dutyCycle; if (brightval == 100) dutyCycle = 255; else if (brightval == 75) dutyCycle = 130; else if (brightval == 50) dutyCycle = 70; else if (brightval == 25) dutyCycle = 20; else if (brightval == 0) dutyCycle = 0; else dutyCycle = ((brightval * 255) / 100); // log_i("dutyCycle for bright 0-255: %d", dutyCycle); ledcWrite(TFT_BL, dutyCycle); } bool getTouched() { return digitalRead(16) == LOW; } struct TP { int16_t x[1], y[1]; }; /********************************************************************* ** Function: InputHandler ** Handles the variables PrevPress, NextPress, SelPress, AnyKeyPress and EscPress **********************************************************************/ void InputHandler(void) { TP t; static unsigned long tm = 0; if (millis() - tm > 200 || LongPress) { // I know R3CK.. I Should NOT nest if statements.. // but it is needed to not keep SPI bus used without need, it save resources if (getTouched()) { touch.getPoint(t.x, t.y, 1); // Serial.printf("\nRAW: Touch Pressed on x=%d, y=%d",t.x, t.y); if (bruceConfigPins.rotation == 3) { t.y[0] = (tftHeight + 20) - t.y[0]; t.x[0] = t.x[0]; } if (bruceConfigPins.rotation == 0) { int tmp = t.x[0]; t.x[0] = tftWidth - t.y[0]; t.y[0] = tftHeight - tmp; } if (bruceConfigPins.rotation == 2) { int tmp = t.x[0]; t.x[0] = t.y[0]; t.y[0] = tmp; } if (bruceConfigPins.rotation == 1) { t.x[0] = tftWidth - t.x[0]; } // Serial.printf("\nROT: Touch Pressed on x=%d, y=%d\n",t.x[0], t.y[0]); if (!wakeUpScreen()) AnyKeyPress = true; else return; // Touch point global variable touchPoint.x = t.x[0]; touchPoint.y = t.y[0]; touchPoint.pressed = true; touchHeatMap(touchPoint); tm = millis(); drv.setWaveform(0, 75); drv.setWaveform(1, 0); // end waveform drv.run(); } } } /********************************************************************* ** Function: powerOff ** location: mykeyboard.cpp ** Turns off the device (or try to) **********************************************************************/ void powerOff() {} /********************************************************************* ** Function: checkReboot ** location: mykeyboard.cpp ** Btn logic to turn off the device (name is odd btw) **********************************************************************/ void checkReboot() {} /*************************************************************************************** ** Function name: isCharging() ** Description: Determines if the device is charging ***************************************************************************************/ bool isCharging() { return axp192.isCharging(); // Return the charging status from AXP }